By Marcie Goodman
Keeping soda machines in good working condition is an important task that needs to be considered. The proper manner of Soda Machine Restoration often begins with the removal and disassembling of the bolts and nuts. When this is done, it results to separation of the machine into smaller components which are easier to clean and those that lead to easy changing of the respective parts.
Bead blasting is the next step that is carried out on the major parts to remove any dirt or grease that could be present on the surfaces. Air is fully compressed in an attempt to blast abrasive grits which is needed on the material surface. This is a cleaning process that removes any stain and dirt together with old paints which have accumulated over time.
Power coating is then carried out on all the drums, liners of the shelves and cabinets to ensure that a rust proof and hard finish is accomplished. It also ensures that the final finish is as shinny as something new. It is better if this is started at the top while handling one section at a time until all the coating is done. Embossed lettering is then added on by painting in order to finish up this step.
Stripping is another important step which is done after determining that a proper chemical ratio has been mixed. This chemical is applied evenly as a coat from bottom to top, to avoid streaking. Special attention should be observed during stripping as this is the point where repair needs can be easily identified.
Placing energy insulation into the interior of the doors and the main unit is then carried out to ensure that the rubbers stay in the required places. Originality of your cooling system will depend on the manner in which it was insulated. This is the reason why better insulation should be carried out.
All chrome should also be polished, depending on the style of the soda machine. The steel screws and bolts that are used should be new and stainless to ensure durability. The bottles and can-stacks together with the shelves should be powder coated or plated with zinc in a correct manner. If this is not done correctly, it may interfere with the functioning procedure or bring about tolerance interference.
Coin mechanisms should be considered and it is better if they function properly without problems. Thorough inspection and cleaning are the techniques which could enable better results. Everyone would have his or her preferred dress-up decals and so, it would be necessary if you choose that decal which suits you best. These decals would then be fixed to the machine.
Handling the refrigeration unit is one last important step in soda machine restoration guide. There are two options which could perfectly work out. Restoring back the original unit to its desired place after disassembling is one choice. However, if you need brand new parts then a new deck compressor could be fixed up and this would see you spend a bit more rather than using the older one.
Bead blasting is the next step that is carried out on the major parts to remove any dirt or grease that could be present on the surfaces. Air is fully compressed in an attempt to blast abrasive grits which is needed on the material surface. This is a cleaning process that removes any stain and dirt together with old paints which have accumulated over time.
Power coating is then carried out on all the drums, liners of the shelves and cabinets to ensure that a rust proof and hard finish is accomplished. It also ensures that the final finish is as shinny as something new. It is better if this is started at the top while handling one section at a time until all the coating is done. Embossed lettering is then added on by painting in order to finish up this step.
Stripping is another important step which is done after determining that a proper chemical ratio has been mixed. This chemical is applied evenly as a coat from bottom to top, to avoid streaking. Special attention should be observed during stripping as this is the point where repair needs can be easily identified.
Placing energy insulation into the interior of the doors and the main unit is then carried out to ensure that the rubbers stay in the required places. Originality of your cooling system will depend on the manner in which it was insulated. This is the reason why better insulation should be carried out.
All chrome should also be polished, depending on the style of the soda machine. The steel screws and bolts that are used should be new and stainless to ensure durability. The bottles and can-stacks together with the shelves should be powder coated or plated with zinc in a correct manner. If this is not done correctly, it may interfere with the functioning procedure or bring about tolerance interference.
Coin mechanisms should be considered and it is better if they function properly without problems. Thorough inspection and cleaning are the techniques which could enable better results. Everyone would have his or her preferred dress-up decals and so, it would be necessary if you choose that decal which suits you best. These decals would then be fixed to the machine.
Handling the refrigeration unit is one last important step in soda machine restoration guide. There are two options which could perfectly work out. Restoring back the original unit to its desired place after disassembling is one choice. However, if you need brand new parts then a new deck compressor could be fixed up and this would see you spend a bit more rather than using the older one.
About the Author:
If you are in need of additional information about soda machine restoration you can gain access to our homepage instantly on the Web. Find out all you need to know by reading the posts on http://www.be-bopjoes.com now!
0 commentaires:
Post a Comment